Bonjour a tous,
Un ami m'a donner son prismcube ruby en panne,
il me dit qu'il as supprimer tous les fichier du décodeur en les supprimant par ftp et que depuis plus rien ne fonctionne et plus moyen d'installer une image avec la clé usb a l’arrière de l'appareil,
J'ai donc essayer avec le logiciel tera term et une emergency image comme indiquer sur un tuto que j'ai trouver sur le net et qui explique comment récupérer un prismcube planté mais absolument rien y fait,
Voici une capture du deroulement de tera term
CCC

Starting Microloader ASM built on Jun 17 2013 20:08:40...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Found Internal Ethernet PHY on GMAC0....
Sampling the UART for input ...
Input any key on UART to stop for flash download
GCS in ISA MODE
GCS: NAND DEVICE SETUP COMPLETE
NAND: Initialization complete
starting UART boot ...
Setting up default ATAG list...
Jumping to Uboot .........




U-Boot 2009.08-dirty (Jun 19 2013 - 13:44:41)


DRAM: 512 MB
malloc: Using memory from 0x04200000 to 0x04400000
GCS: Setup In ISA MODE
UART Boot not Supported .....
GCS: NAND DEVICE SETUP COMPLETE
Boot Device: NAND Flash
NAND: 512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
In: serial
Out: serial
Err: serial
Net: lip0
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
./
../
4790 checkusb.img
61 checkusb.img.md5
3099044 kernel.uimage
62 kernel.uimage.md5
27277158 ramdisk.gz
59 ramdisk.gz.md5
1300 ramdisk_update_script.sh
73 ramdisk_update_script.sh.md5
626412 u-boot.bin
59 u-boot.bin.md5
3022529 uimage
55 uimage.md5
52000 uldr.bin
57 uldr.bin.md5
65536 uldr.bin.uartboot_img
56 uldr.bin.uartboot_img.md5


16 file(s), 2 dir(s)


reading update_ruby/checkusb.img


4790 bytes read


NAND erase: device 0 offset 0x17d00000, size 0x2d00000
Erasing at 0x1a9e0000 -- 100% complete.
OK
Unknown command 'display_strings' - try 'help'
Unknown command 'display_strings' - try 'help'
Unknown command 'check_update' - try 'help'
Unknown command 'write_vfd' - try 'help'
Unknown command 'display_strings' - try 'help'
Unknown command 'display_strings' - try 'help'


NAND read: device 0 offset 0x1700000, size 0x600000
NAND read from offset 1700000 failed -74
6291456 bytes read: ERROR
## Booting kernel from Legacy Image at 04400000 ...
Image Name: uImage
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 3097868 Bytes = 3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.34 (amedeo@meohome) (gcc version 4.7.2 (GCC) ) #1 SMP Tue Mar 17 17:50:05 CET 2015
[ 0.000000] CPU: ARMv7 Processor [411fc091] revision 1 (ARMv7), cr=10c57c7d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ca che
[ 0.000000] Machine: NXP BL-STB platform
[ 0.000000] ChipID=0x2 ChipRevID=0x2
[ 0.000000] EMAC address found in ATAG list ...
[ 0.000000] Mac 0 address bytes = 00:00:de:ad:be:f0
[ 0.000000] Mac 1 address bytes = 00:00:de:ad:be:f1
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] Early platform io descriptors mapping...
[ 0.000000] PERCPU: Embedded 7 pages/cpu @805fb000 s6816 r8192 d13664 u65536
[ 0.000000] pcpu-alloc: s6816 r8192 d13664 u65536 alloc=16*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 129536
[ 0.000000] Kernel command line: noinitrd console=ttyS1,115200n8 mtdparts=nx_ 2017:1024k@0k(uldr),1792k@1024k(u-boot),20m@3m(configure),6m@23m(kernel),350m@29 m(root),45m@381m(update),5m@426m(uImage),35m@431m( ramdisk),-(extra) ubi.mtd=4 ro ot=ubi0:rootfs rootfstype=ubifs rw rootflags=sync ldver=4 hwver=1 videomode=PAL
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 323296k/323296k available, 200992k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xa0800000 - 0xd0000000 ( 760 MB)
[ 0.000000] lowmem : 0x80000000 - 0xa0000000 ( 512 MB)
[ 0.000000] modules : 0x7e800000 - 0x80000000 ( 24 MB)
[ 0.000000] .init : 0x80008000 - 0x80030000 ( 160 kB)
[ 0.000000] .text : 0x80030000 - 0x80574000 (5392 kB)
[ 0.000000] .data : 0x80596000 - 0x805ccce0 ( 220 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, N odes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:388
[ 0.000000] Initializing Cortex Interrupt Distributer (DISTR) at Vir:0xE01010 00 = Phy:0xE0101000
[ 0.000000] Initializing Cortex Generic Interrupt Controller (GIC) at Vir:0xE 0100100 = Phy:0xE0100100
[ 0.000000] Initializing Cortex A9 Global Timer at Vir:0xE0100200 = Phy:0xE01 00200, using Irq:27, at Freq:250000000
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [ttyS1] enabled
[ 0.010000] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736)
[ 0.280000] Mount-cache hash table entries: 512
[ 0.280000] Initializing cgroup subsys devices
[ 0.290000] CPU: Testing write buffer coherency: ok
[ 0.290000] Calibrating local timer... 249.49MHz.
[ 0.360000] L310 cache controller enabled
[ 0.360000] l2x0: 8 ways, CACHE_ID 0x410004c4, AUX_CTRL 0x22021001, Cache siz e: 131072 B
[ 0.370000] Brought up 1 CPUs
[ 0.370000] SMP: Total of 1 processors activated (996.14 BogoMIPS).
[ 0.380000] devtmpfs: initialized
[ 0.380000] NET: Registered protocol family 16
[ 0.390000] Adding platform devices...
[ 0.390000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counter s available
[ 0.400000] SATA: Adjusting los_lvl (rd_val=0x8a46, wr_val=0x8ae6)
[ 0.410000] SATA: Adjusting rx_term_en0/1 (rd_val=0x2750275, wr_val=0x2770277 )
[ 0.420000] bio: create slab <bio-0> at 0
[ 0.420000] vgaarb: loaded
[ 0.430000] SCSI subsystem initialized
[ 0.430000] usbcore: registered new interface driver usbfs
[ 0.440000] usbcore: registered new interface driver hub
[ 0.440000] usbcore: registered new device driver usb
[ 0.450000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.450000] Switching to clocksource global_timer_src
[ 0.460000] NET: Registered protocol family 2
[ 0.460000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.470000] TCP established hash table entries: 16384 (order: 5, 131072 bytes )
[ 0.480000] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.480000] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.490000] TCP reno registered
[ 0.490000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.500000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.500000] NET: Registered protocol family 1
[ 0.510000] RPC: Registered udp transport module.
[ 0.510000] RPC: Registered tcp transport module.
[ 0.520000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.520000] PMU: registered new PMU device of type 0
[ 0.530000] PM: Apollo power mgmt initialization.
[ 0.540000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.550000] Registering unionfs 2.5.4 (for 2.6.34-rc0)
[ 0.560000] JFFS2 version 2.2. (NAND) (SUMMARY) c 2001-2006 Red Hat, Inc.
[ 0.560000] SGI XFS with security attributes, realtime, large block/inode num bers, no debug enabled
[ 0.570000] msgmni has been set to 631
[ 0.580000] alg: No test for stdrng (krng)
[ 0.580000] io scheduler noop registered
[ 0.590000] io scheduler cfq registered (default)
[ 0.590000] nx_dmac_1902 nx_dmac_1902.1: NXP DMA Controller IP_1902 found @ [ a08ba000] (rev 41080), 8 channels
[ 0.610000] uart-ip3106.0: ttyS0 at MMIO 0xe06e1000 (irq = 46) is a uart-ip31 06
[ 0.620000] uart-ip3106.1: ttyS1 at MMIO 0xe06e2000 (irq = 47) is a uart-ip31 06
[ 0.630000] uart-ip3106.2: ttyS2 at MMIO 0xe06e3000 (irq = 48) is a uart-ip31 06
[ 0.630000] uart-ip3106.3: ttyS3 at MMIO 0xe06e4000 (irq = 49) is a uart-ip31 06
[ 0.640000] nx_dmac: Registered with 8 channels
[ 0.650000] brd: module loaded
[ 0.660000] loop: module loaded
[ 0.660000] Uniform Multi-Platform E-IDE driver
[ 0.670000] ide-gd driver 1.18
[ 0.670000] sata-apollo sata-apollo.0: AHCI 0001.0100 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 0.680000] sata-apollo sata-apollo.0: flags: ncq sntf stag pm led clo only p mp pio slum part ccc sxs
[ 0.690000] scsi0 : sata-apollo
[ 0.690000] scsi1 : sata-apollo
[ 0.690000] ata1: SATA max UDMA/133 ahci 0xa08d2000 port 0xa08d2100 irq 39
[ 0.700000] ata2: SATA max UDMA/133 ahci 0xa08d2000 port 0xa08d2180 irq 39
[ 0.710000] nx_2016 nx_2016: map_probe failed
[ 0.720000] nx_2016: probe of nx_2016 failed with error -5
[ 0.720000] ONFI flash detected
[ 0.730000] ONFI param page 0 valid
[ 0.730000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix H27U4G8F 2DTR-BC)
[ 0.740000] 9 cmdlinepart partitions found on MTD device nx_2017
[ 0.740000] Creating 9 MTD partitions on "nx_2017":
[ 0.750000] 0x000000000000-0x000000100000 : "uldr"
[ 0.760000] 0x000000100000-0x0000002c0000 : "u-boot"
[ 0.760000] 0x000000300000-0x000001700000 : "configure"
[ 0.770000] 0x000001700000-0x000001d00000 : "kernel"
[ 0.770000] 0x000001d00000-0x000017b00000 : "root"
[ 0.780000] 0x000017d00000-0x00001aa00000 : "update"
[ 0.780000] 0x00001aa00000-0x00001af00000 : "uImage"
[ 0.790000] 0x00001af00000-0x00001d200000 : "ramdisk"
[ 0.790000] 0x00001d200000-0x000020000000 : "extra"
[ 0.800000] UBI: attaching mtd4 to ubi0
[ 0.800000] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.810000] UBI: logical eraseblock size: 126976 bytes
[ 0.820000] UBI: smallest flash I/O unit: 2048
[ 0.820000] UBI: VID header offset: 2048 (aligned 2048)
[ 0.830000] UBI: data offset: 4096
[ 1.070000] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.440000] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.930000] UBI: max. sequence number: 213
[ 1.950000] UBI: attached mtd4 to ubi0
[ 1.950000] UBI: MTD device name: "root"
[ 1.960000] UBI: MTD device size: 350 MiB
[ 1.960000] UBI: number of good PEBs: 2800
[ 1.970000] UBI: number of bad PEBs: 0
[ 1.970000] UBI: number of corrupted PEBs: 0
[ 1.980000] UBI: max. allowed volumes: 128
[ 1.980000] UBI: wear-leveling threshold: 4096
[ 1.990000] UBI: number of internal volumes: 1
[ 1.990000] UBI: number of user volumes: 1
[ 1.990000] UBI: available PEBs: 0
[ 2.000000] UBI: total number of reserved PEBs: 2800
[ 2.000000] UBI: number of PEBs reserved for bad PEB handling: 28
[ 2.010000] UBI: max/mean erase counter: 136/63
[ 2.010000] UBI: image sequence number: 1077297098
[ 2.020000] Atmel at76x USB Wireless LAN Driver 0.17 loading
[ 2.020000] usbcore: registered new interface driver at76c50x-usb
[ 2.030000] usbcore: registered new interface driver zd1201
[ 2.040000] GMAC:Internal PHY being used with GMAC0
[ 2.040000] GMAC:Registering Ethernet ISR number 40
[ 2.050000] GMAC:Ethernet interface eth0 registered
[ 2.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.060000] usb-ip9028 usb-ip9028.0: IP9028 embedded EHCI USB controller
[ 2.060000] usb-ip9028 usb-ip9028.0: new USB bus registered, assigned bus num ber 1
[ 2.070000] UBI: background thread "ubi_bgt0d" started, PID 41
[ 2.100000] usb-ip9028 usb-ip9028.0: irq 93, io base 0xe066c000
[ 2.120000] usb-ip9028 usb-ip9028.0: USB 2.0 started, EHCI 1.00
[ 2.120000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.130000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.130000] usb usb1: Product: IP9028 embedded EHCI USB controller
[ 2.140000] usb usb1: Manufacturer: Linux 2.6.34 ehci_hcd
[ 2.150000] usb usb1: SerialNumber: ip9028
[ 2.150000] hub 1-0:1.0: USB hub found
[ 2.150000] hub 1-0:1.0: 1 port detected
[ 2.160000] usb-ip9028 usb-ip9028.1: IP9028 embedded EHCI USB controller
[ 2.170000] usb-ip9028 usb-ip9028.1: new USB bus registered, assigned bus num ber 2
[ 2.200000] usb-ip9028 usb-ip9028.1: irq 94, io base 0xe066d000
[ 2.220000] usb-ip9028 usb-ip9028.1: USB 2.0 started, EHCI 1.00
[ 2.220000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.230000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.230000] usb usb2: Product: IP9028 embedded EHCI USB controller
[ 2.240000] usb usb2: Manufacturer: Linux 2.6.34 ehci_hcd
[ 2.250000] usb usb2: SerialNumber: ip9028
[ 2.250000] hub 2-0:1.0: USB hub found
[ 2.250000] hub 2-0:1.0: 1 port detected
[ 2.260000] usb-ip9028 usb-ip9028.2: IP9028 embedded EHCI USB controller
[ 2.270000] usb-ip9028 usb-ip9028.2: new USB bus registered, assigned bus num ber 3
[ 2.270000] usb-ip9028 usb-ip9028.2: irq 95, io base 0xe066e000
[ 2.300000] usb-ip9028 usb-ip9028.2: USB 2.0 started, EHCI 0.00
[ 2.300000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.310000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 2.310000] usb usb3: Product: IP9028 embedded EHCI USB controller
[ 2.320000] usb usb3: Manufacturer: Linux 2.6.34 ehci_hcd
[ 2.330000] usb usb3: SerialNumber: ip9028
[ 2.330000] hub 3-0:1.0: USB hub found
[ 2.330000] hub 3-0:1.0: 0 ports detected
[ 2.340000] usbcore: registered new interface driver cdc_wdm
[ 2.340000] usbcore: registered new interface driver libusual
[ 2.350000] mice: PS/2 mouse device common for all mice
[ 2.360000] rtc_apollo rtc_apollo: rtc core: registered rtc_apollo as rtc0
[ 2.360000] i2c /dev entries driver
[ 2.370000] sdhci: Secure Digital Host Controller Interface driver
[ 2.370000] sdhci: Copyright(c) Pierre Ossman
[ 2.380000] usbcore: registered new interface driver usbhid
[ 2.380000] usbhid: USB HID core driver
[ 2.390000] oprofile: using arm/armv7-ca9
[ 2.390000] TCP cubic registered
[ 2.400000] NET: Registered protocol family 17
[ 2.400000] lib80211: common routines for IEEE802.11 drivers
[ 2.410000] ThumbEE CPU extension supported.
[ 2.410000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 1
[ 2.420000] rtc_apollo rtc_apollo: setting system clock to 1970-01-01 00:00:0 0 UTC (0)
[ 2.430000] UBIFS: parse sync
[ 2.430000] UBIFS: background thread "ubifs_bgt0_0" started, PID 44
[ 2.460000] UBIFS: recovery needed
[ 2.560000] UBIFS: recovery completed
[ 2.570000] UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)
[ 2.570000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes : 2048 bytes/2048 bytes
[ 2.580000] UBIFS: FS size: 350072832 bytes (333 MiB, 2757 LEBs), journal siz e 9023488 bytes (8 MiB, 72 LEBs)
[ 2.590000] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 2.600000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID CDF246A6-2C24- 4A4D-B6CF-2EDBF9BC1037, small LPT model
[ 2.610000] usb 2-1: new high speed USB device using usb-ip9028 and address 2
[ 2.620000] VFS: Mounted root (ubifs filesystem) on device 0:14.
[ 2.620000] devtmpfs: mounted
[ 2.630000] Freeing init memory: 160K
/sbin/init: error while loading shared libraries: libkmod.so.2: cannot open shar ed object file: No such file or directory
[ 2.700000] Kernel panic - not syncing: Attempted to kill init!
[ 2.700000] [<80037450>] (unwind_backtrace+0x0/0xf8) from [<80447500>] (panic +0x48/0xb8)
[ 2.710000] [<80447500>] (panic+0x48/0xb8) from [<800530bc>] (do_exit+0x698/0 x6bc)
[ 2.720000] [<800530bc>] (do_exit+0x698/0x6bc) from [<80053360>] (do_group_ex it+0x3c/0xcc)
[ 2.720000] [<80053360>] (do_group_exit+0x3c/0xcc) from [<80053400>] (__wake_ up_parent+0x0/0x18)
le decodeur indique UPDATE sur la face avant et une lampe rouge clignotante mais rien d'autre ne ce produit ??

Si quelqu'un peut m'aider a résoudre ce problème?

Merci infiniment